TRODAT (Shandong) Marine Engineering Co., Ltd
+86-0536-2222696
Contact Us

Regarding The Maintenance Of Slurry Pumps

Jan 15, 2025

Seven Precautions for the Maintenance of Slurry Pumps

The maintenance of slurry pumps is a crucial aspect in the application of slurries. Whether the slurry pump is in use or not, maintenance work should be carried out in accordance with the instructions in the pump manual. Just as a car needs regular maintenance, the maintenance of a slurry pump is equally important as it can reduce production costs.

 

The specific maintenance methods for slurry pumps are as follows:

1.Avoid slurry leakage from the shaft seal of the slurry pump. Adjust the tightness of the packing in a timely manner; ensure that the bearing water pressure and water volume meet the requirements as specified.

2.Replace the shaft sleeve of the slurry pump in a timely manner. When replacing the bearing, ensure a dust - free and clean environment.

3.Ensure an appropriate temperature during normal operation. Generally, when the pump is operating normally, the temperature of the bearing should preferably be between 60 - 65°C.

4.Ensure that the elastic pad in the coupling of the slurry pump is correctly and completely installed; guarantee the co - axiality of the pump and the motor.

5.Ensure that the installation of the components of the slurry pump and the pipeline system is correct and firm.

6.Pay attention to the easily worn parts of the slurry pump and maintain and replace them in a timely manner.

7.Avoid blockage at the suction port during operation and ensure that there is no air leakage in the suction pipeline system of the slurry pump.

Common Faults of Slurry Pumps and Their Solutions

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. The slurry pump does not absorb water

Causes:

Air leakage in the suction pipeline or at the packing.

Incorrect rotation direction or damaged impeller.

Blockage in the suction pipe.
Solutions:

Seal the leaking part.

Check the rotation direction and replace with a new impeller.

Remove the blockage.

 

2. Excessive shaft power of the slurry pump

Causes:

The packing gland is too tight, causing the packing to heat up.

Friction occurs inside the pump.

The bearing is damaged.

The drive belt is too tight.

The pump flow rate is too large.

The rotational speed is too high, and the specific gravity is large.

The motor shaft and the pump shaft are misaligned or not parallel.
Solutions:

Loosen the bolts of the packing gland.

Eliminate the friction.

Replace the bearing.

Adjust the belt.

Adjust the operating conditions of the pump.

Adjust the rotational speed.

Adjust the motor shaft and the pump shaft.

 

3. Overheating of the pump bearing

Causes:

Excessive or insufficient bearing grease (oil).

There are impurities in the grease (oil).

The bearing is damaged.
Solutions:

Adjust the amount of grease (oil) appropriately.

Replace with new grease (oil).

Replace with a new bearing.

 

4. Short bearing life of the pump

Causes:

The motor shaft and the pump shaft are misaligned or not parallel.

The shaft is bent.

There is friction inside the pump or the impeller is unbalanced.

Foreign objects enter the bearing or the amount of grease is inappropriate.

The bearing is improperly assembled.
Solutions:

Adjust the motor shaft and the pump shaft.

Replace the shaft.

Eliminate the friction and replace with a new impeller.

Clean the bearing.

Re - assemble the bearing.

 

5. Severe leakage at the pump packing

Causes:

The packing is severely worn.

The shaft sleeve is severely worn.

The sealing water is not clean.
Solutions:

Replace with new packing.

Replace the shaft sleeve.

Replace with clean sealing water.

 

6. High vibration and noise of the pump

Causes:

The bearing is damaged.

The impeller is unbalanced.

Air enters the suction pipe or it is blocked.

The flow rate is uneven and the pump is running dry.
Solutions:

Replace with a new bearing.

Replace with a new impeller.

Eliminate the air intake and clean the blocked part.

Improve the feeding conditions of the pump.

 

We support product customization services

TRODAT is a manufacturer of marine equipment and we have an excellent team to provide a full range of spare parts, maintenance support, equipment training programs, dredging consulting services, and hands-on instruction and commissioning of dredging operators..

Our address

3F, Building 3, Headquarter of Brocade Group, No.9 Gangxing Road, Jinan, Shandong Province, P.R. China

Whats App

(86) 18953611135

E-mail

trodat@trodatgroup.com