TRODAT (Shandong) Marine Engineering Co., Ltd
+86-0536-2222696
Contact Us

Anchors Working Method

Apr 07, 2024

The fact that an anchor can "brake" a ship is largely due to the physics of anchors.

Anchors Working Method

The anchor claw is the most important part of the anchor that grabs into the soil. After the ship lays at anchor, the anchor sinks to the bottom of the water under the traction of the anchor chain. At the bottom of the water, anchor rods give forces thus the wrist the anchor located at a surface which will be perpendicular to the bottom surface. At this time, the anchor claw contacts the bottom of the water. The length of anchor chain is often greater than the water depth. Therefore, the anchor chain lays at the bottom surface.

When a ship is disturbed (such as in waves), the anchor chain will be pulled, and the anchor at the bottom of the water will be subjected to a horizontal force at the anchor chain connection. At the same time, the gravity of the anchor itself acts on the contact point between the anchor claw and the water bottom. The combination of the two forces causes the anchor to move diagonally downwards. Those are steps of anchoring into the soil. After the anchor is pulled into the water bottom, it can provide the ship with the ability to anchor.

The anchor is equivalent to a handbrake of a car, and is an indispensable equipment to ensure the safety of the ship. The main function of anchor is to fix and stabilize the ship, preferably by hooking a fixed object in the water. Another factor that stops the ship in the water is the anchor chain, and the weight of the anchor chain is also an important factor in securing the ship.

R-C

The process of anchoring; the anchor starts with the crown of the anchor touching the bottom, then the body of the anchor lays down, at which point the tip of the anchor claw will also touch the bottom under the action of the balance bar, but will not catch in the sand and gravel. The boat will continue to drop a certain length of anchor chain so that most of it lies flat on the bottom.

It is not possible to anchor anywhere, the best substrate is sand and rocky bottom, followed by mud bottom, and reef substrate will be difficult to anchor on, it may be difficult to create a grip, or it may be difficult to lift the anchor because it is stuck in the rocks. It may be difficult to create grip, or it may get stuck in the rocks and be difficult to anchor. The depth of water is too great, for example, in the ocean, three or four thousand metres deep, and it is not suitable for anchoring either. Whether those places are suitable for anchoring is actually marked on the charts in advance, and experienced sailors know that.

P37966397b1468d06dfcfd58fe56c0fa0fe532f

Condition and operation of boat anchor:

When dropping the anchor, do not use too much speed, but slowly lower the anchor; too much speed will cause difficulty in braking the anchor and anchor chain, which may damage the anchor engine and may even have other serious consequences. The boat will continue to drop a certain length of anchor chain so that most of it is flat on the bottom. At this point, moving backwards and dragging the anchor chain backwards slightly, the anchor claw D is inserted into the sand and gravel by the combined force of gravity on the anchor body and the pull of the anchor chain.

At this point, the vessel will retrieve some of the anchor chain slightly. In general, the length of the released anchor chain should be 3-5 times the water depth. If the anchor chain is too long, the range of manoeuvre of the ship will be increased and it will be easy to collide with other anchored ships. If the anchor chain is too short, it is easy to pull the anchor body upwards, which will make the anchor loose and lose the grip effect. After the anchor grabs the ground, it is equivalent to hitting a ground stake, while the anchor chain, after dropping, basically only has the pulling force at the level of the substrate, at which the anchor's gripping force is the largest.

When lifting the anchor, the ship moves forward while slowly retracting the anchor chain, and at a point closer to the anchor, straighten the anchor chain, at this time, the point A of the anchor rod will be lifted up under the tension of the anchor chain, and the anchor will be lifted out of the substrate with the anchor crown B as the axis, and the anchor claw D will be lifted out from the substrate by using the principle of leverage, then the ship will continue to retract the anchor chain until the anchor is pulled out of the water.

The above is the working principle of the anchor, do you understand now?