TRODAT (Shandong) Marine Engineering Co., Ltd
+86-0536-2222696
Contact Us

Attentions During Using Dredging Slurry Pump

Apr 01, 2024

 

1. When the pump is used when the content of solids in the medium is more than 40%, the medium should be diluted to the working range with clean water.
2. Pumping sand during the pumping, never allowed to shut down, shut down the pump without stopping the state, up to the clear water layer of work for 5 minutes.
3. The pump is used when the pumping medium is 40% of solids, and should not be shut down, as the shutdown will easily cause the outlet to be clogged with mud and sand.
4. In the clogging of the outlet, must manually clean up the mud and sand in the outlet pipe, clean up smooth before starting again.
5. When the pump is raised, the pump should be kept in normal operation to ensure that there is no leakage of electricity, and then slowly lift the pump away from the working surface and lift it up to the clear water level to work.
The pump should be lifted out of the working surface slowly, and then lift it to the clear water level to work for 5 minutes.
6. Don't pull the cable when the pump and water pump are working, so as not to tear the cable, resulting in leakage or water ingress into the motor and burn the motor.
7. The water pump must not directly contact the sand layer, there must be 100-500mm gap. The pump must be suspended from the upper part of the positioning, pontoon or working platform can be, in order to prevent the pump from drilling into the sand layer.
8. The pump is not full flow, full head type pump, is strictly prohibited below 80% of the rated head continuous operation (such as ordering full head).
If you order full-lift pumps, please specify when ordering).
9. After two months of smooth operation of the pump, please check the oil chamber, if the oil in the oil chamber is blackened or there are a lot of impurities, please replace the oil and check the seals.
If the oil in the oil chamber is blackened or there are a lot of impurities, please replace the oil and check whether the seal needs to be replaced.
10. The pump must be operated in all potential water, and must not be exposed to the water surface.

2

Use conditions
1. 50Hz, 60Hz/230V, 380V, 415V, 660V three-phase AC power supply, the capacity of the distribution transformer is 2-3 times the rated capacity of the motor. (Specify the power supply conditions when ordering)
2. The working position in the medium is vertical, and the working condition is continuous.
3. Diving depth of the unit: not more than 50 metres, the minimum diving depth is subject to the submerged motor.
4. Maximum concentration of solid particles in the medium: 45% for ash, 60% for slag.
5. The temperature of the medium shall not exceed 60℃, R-type (high temperature) shall not exceed 140℃, and it does not contain flammable and explosive gases.
Scope of application
1. Absorb yellow sand under the water of rivers, lakes and seas.
2. Dredging projects of rivers, lakes, reservoirs, urban inland waterways, etc.
3. Deep-water dredging projects such as harbours, wharves, waterways, sediment management, etc.; and
4. Sedimentation tank slurry, sediment, sand and gravel cleaning in sewage treatment plants, iron and steel plants, thermal power plants, etc.; and
5. Sand removal and desilting of large calibre deep wells, sand piles, municipal pipelines and bridge abutment construction; and
6. High-temperature slag, boiler high-temperature slurry, heat-resistant iron oxide, metallurgy and other high-temperature slurry discharge.
7. Diamond sand, tailings mine, quartz sand mine, rare earth mine and other extraction of mineral powder, mortar and so on.
8. Coastal land reclamation, sand reclamation, power station water storage and sand transfer, etc.; and
9. Coal washing slurry, coal slag, power plant fly ash slurry, coal slurry extraction, transport;

10, ceramics, marble powder and other slurry materials, removal work;

11. Conveyance of other slurry media containing large solid particles.

-2